Plastic hot tubs, production of plastic hot tubs

You can order a font made of polypropylene or wood at a competitive price.

We offer high-quality products that are created by experienced specialists.

All hot tubs for baths and saunas are distinguished by reasonable cost, long service life, resistance to numerous influences, ease of operation and maintenance.

The hot tubs are made from safe, environmentally friendly materials: polypropylene and wood

.

Polypropylene hot tub

will be an excellent alternative to a full-fledged pool or its addition (
read more about the benefits of polypropylene
).

◊ Font made of natural wood

will be a great addition to your sauna!
In such a font you will be able to fully enjoy all the beneficial phyto-properties of wood ( the technology of manufacturing wooden fonts
,
the advantages of wooden fonts “The Fifth Element”
).

Material for making a font

The most common material for making a font is wood or plastic, or rather polypropylene. Bathtubs made of wood look aesthetically presentable, but these types of bathtubs have one significant drawback: the wood shrinks when it dries.

To give an analogy for comparison, a wooden font, like a barrel, must be constantly in a humid environment in order to avoid shrinkage of the wood and the natural appearance of cracks in the sides of the product. So, recently, bath fonts made from blue polypropylene have become increasingly popular. Thanks to the modern properties of the plastic used, polypropylene hot tubs do not require much attention to operate. In everyday care they are no different from enamel bathtubs; it’s also easy enough to wash with a cleaning agent and that’s it.

Water supply made from polypropylene pipes

The source of water can be either a central water supply or a well or borehole. You should start with exterior work.

Exterior works

A trench 70-100 cm deep is dug from the water source. Then a metal-plastic pipe (more suitable for outdoor use) with a diameter of 3.2 cm is laid. Having made a 90° turn (a connecting corner is used), the pipe is brought into the room and connected to the pumping station ( provided that it is provided for in the diagram), is removed from it and closed with a brass fitting that goes to the thread (the diameter is the same). Next, a tee equipped with a drain valve is attached, but in the case of high-quality insulation of the outer pipe, you can do without it. Then an “American” is installed, equipped with a shut-off valve to stop/resume the water supply. If necessary, install a filter, then switch to a PP pipeline with a diameter of 2.5 cm.

Connection diagram

The collector will be the first of these pipes. Essentially, it is a pipe equipped with holes for wiring. The manifold is necessary so that the wiring starts correctly and the same pressure is created in the pipes. All pipes leading from the collector must be equipped with shut-off valves, allowing the water to be turned off in emergency situations or during maintenance.

Collector

Interior work

One of the pipes leads from the collector to the water heater (if water is used frequently and the source does not have time to renew, you can install a storage boiler). At the outlet of the hot water boiler, another ball valve is installed, then the pipe is led to the plumbing fixture. For other appliances where hot water is not required, pipes are led directly from the collector.

Important information! On the pipe section between the boiler and the collector, you need to additionally install a fuse and a 5-liter damper tank. The latter will compensate for the expansion of the liquid when heated, and also prevent shocks in the system after a long period of inactivity of the boiler.

As already noted, all metal elements are connected using “American wires” for the purpose of easy disconnection during repairs.

American (sleeve nut)

And now directly to the wiring. After drawing up its project, you need to prepare everything you need for welding work - an electric jigsaw and a soldering iron for PP pipes. First, a nozzle of the required diameter is put on the soldering iron, then the temperature is set to the device (usually 270°) and it warms up. Further actions are performed according to the following algorithm.

Step 1 . Using pre-made markings, the pipes are cut into pieces of the required length.

Marking

Step 2. Burrs on the ends are carefully removed.

Deburring

Step 3. The depth of insertion of the product into the fitting is indicated by a marker. Typically, the end should not come into contact with the fitting coupling - a slight gap is required (about 1 mm).

Fitting

Step 4. Both elements are put on the nozzle for uniform heating. The duration of heating, as well as cooling, is related to the diameter and is indicated in the table below.

Heating duration

Step 5. The heated elements are removed and joined in accordance with the marks, after which they are pressed onto each other with little force. You cannot rotate the elements along the axis during connection!

Docking

Step 6. Adjustments can be made within a few seconds after attachment (see table), then the elements are fixed.

Important information! The order of connecting all parts is determined in advance.

Step 7. All wiring elements are connected in a similar way along pre-marked lines. In order to compensate for thermal expansion, it is advisable to use movable fasteners.

The presence of cracks or gaps in the connections is unacceptable. 1 hour after installation is complete, you can turn on the water supply and check the system. Hydrotesting can be carried out no earlier than every other day.

Video - Installation of PP pipes

How to fit a plastic font into the interior?

The plastic font fits amazingly perfectly into any interior. Thanks to the strong body, it can be manufactured according to your individual dimensions with curves that match the interior of your sauna or relaxation room. Fonts made of polypropylene are easy to decorate. For decoration, valuable wood, tiles and marble tiles, mosaics and many other various decorative elements are often used. The bathhouse was and remains a very popular way to relax and cleanse your body of dirt and fatigue, and your head of sad thoughts. In addition, this is also a very useful procedure, especially if, in addition to sitting in the steam room for a long time, you use contrasting cold water and repeat such procedures several times. invites you to buy a plastic font, which will allow you to comfortably conduct such events.

Product Description

is a large manufacturer of a wide variety of devices and containers made of polymer ethylene and propylene. A plastic bathtub made by us is not only a convenient and comfortable way to take water procedures. They have many advantages, including:

• ease of processing - you can use the most common detergents to clean them;
• ability to withstand high temperatures up to – 120 degrees;
• resistance to sudden changes in temperature;
• Absolutely environmentally friendly and safe for health;
• light weight, which makes their transportation and installation extremely simple;
• long service life, estimated in decades;
• low price.

In addition, unlike traditional wooden ones, plastic does not absorb water, does not swell, does not shrink, and will not begin to rot after prolonged use.

If you are interested in a high-quality and durable plastic bathtub, the price of which will be affordable for you, I am ready to help you with this.

Range:

In our company you can buy plastic hot tubs of any shape and size. Typical options include:

• rectangular;
• oval;
• round;
• square;
• corner.

As for the volume of containers, we can find options from 900 to 20,000 liters. The same applies to linear dimensions. But if you have any special preferences, then we are always ready to make containers for you according to your drawings.

In addition, our hot tubs can be equipped with a wide variety of equipment, including lighting, a water heating system and much more.

If you want to buy a cheap plastic hot tub, contact us in any way possible. Our experts will be able to advise you on any questions of interest and help you decide on the specific parameters of the product.

Reasons for the popularity of plastic

Ventilation structures made of plastic elements have gained wide popularity in various areas of human life. This is due to their attractive appearance and numerous advantages over traditional metal competitors.

Note! The most widely used parts are made of polyvinyl chloride (PVC), polyurethane and polypropylene.

The following positive aspects of plastic ventilation are highlighted:

1. No corrosion. This advantage most often determines the choice of plastic. Any metal (even stainless steel) in ventilation systems where steam condensation occurs and the aggressive effects of various substances that pollute the air are susceptible to corrosion. Plastic is absolutely resistant in this regard.
2. Low cost. Plastic systems have a significantly lower price compared to metal, which provides increased resistance to corrosion.
3. Simplicity and quality of installation. When installing metal boxes and pipes, problems always arise in places where there are knocks, requiring rolling, welding, and other operations. Cutting and joining plastic elements is not difficult, and the ends are easy to process and align. Thus, sealing plastic boxes is much easier to ensure.
4. Light weight. This advantage is ensured by ease of installation at the installation site and transportation when delivering the goods.
5. Plastic elements are resistant to water, steam, aggressive environments, and ultraviolet rays. They meet all sanitary standards under normal conditions.

Installation of PVC pipes for ventilation

Bath font

In Russian history, from time immemorial, the tradition of washing in a bathhouse has been widespread, and one of the main features of the Russian bathhouse is a sharp, shock drop in body temperature to increase blood flow in the body and improve well-being. But how to achieve a sharp temperature change when there is no ice hole nearby? Of course, you can use a cold shower, but under it the body cools down gradually. And only a dip in an ice bath can provide you with a sharp shock drop after going to the steam room in the baths. Nowadays, a bathhouse is considered an integral part of a good rest. Various types of fonts are being developed for the bathhouse, which can also be used as pools for a more relaxing recovery of the body.

Our production company creates bathhouses from standard sizes to bathtubs based on private, individually prepared projects.

Blumenberg

Blumenberg wooden hot tubs are manufactured in a family workshop with over 100 years of history. The company's product range includes wooden bathtubs, hydromassages, showers, sinks and accessories for baths and saunas. All products are manufactured in Germany, in Willensen. It has been supplied to the Russian Federation since the 90s.

Product features and range

All Blumenberg hot tubs are made from larch or flounder wood. Flounder is a dense wood; ships are even made from it. This wood comes from Africa, so it is more expensive than larch and most other types of wood raw materials.

The company's technologists use waterproof coatings as a matter of principle; outdoor models are additionally treated with anti-UV varnish. Sawn rivets are glued and sanded in such a way that after finishing it acquires a “furniture look”.

The model range is limited to single and double tanks.
Be sure to check the equipment with your official partner, because up to five different sets of accessories are offered for each model. Characteristics of Blumenberg hot tubs

Form	Oval
Material	Larch, flounder
Coating	Polyurethane, UV protection varnish
Attaching the hoops	Screw connection
Dimensions, H×D×W, cm	100×(100…130)×(72..79)
Equipment	Container, bench, hanging ladder, steel overflow.Additional: choice between galvanized or stainless steel hoops, additional steps, additional bench.
Estimated cost, rub.	From RUB 77,349 for a larch model 100×100×72 (H×D×W) cm up to 198,092 rubles. for a flounder container 110×130×79 cm.

Conclusion:

If you need a hot tub that looks like lacquered furniture, and the emphasis is not on the woody smell, but on beauty and durability, then Blumenberg products are suitable for you. These are compact models from the premium price segment for modern baths and saunas with an area of ​​10 m² or more.

Plastic font

Let us analyze with you the production of a font for relaxation in a bathhouse from the most common material at the moment, this is blue polypropylene. Of all the varieties of materials used to create a hot tub, plastic is the most ideal material, and to be more precise, blue-blue polypropylene. A plastic hot tub, unlike its wooden counterparts, does not require additional, more complex care. Since plastic is not subject to rotting and cracking, the service life of a polypropylene bathtub is many times greater than that of other analogues.

Additional items

In addition to the indicated elements used when installing a ventilation system in a bathhouse, plastic parts are used that perform protective and regulatory functions. These include various dampers, hatches and grilles.

Plastic ventilation grilles

Plastic grilles can have different purposes. The following main varieties are distinguished:

• inertial type: for flow separation without pressurization;
• adjustable grilles: allow you to change the volume of incoming air and distribution in one direction while blocking air movement in the other;
• unregulated type: distribution or flow restrictions without the possibility of regulation;
• external protective grilles: to prevent foreign bodies from entering the channel.

Exhaust grilles can be of an adjustable type.
Plastic hatches can be installed in powerful, branched systems to allow access to the ventilation line for inspection, cleaning, and repair. They can be mounted on the ceiling or walls of the bathhouse. Door-style flaps are designed to allow access to natural flow. They can be mounted on natural ventilation vents in a window or door. Standard sizes are 10x10, 15x30 and 25x60 cm.

Why is it worth buying polypropylene bath fonts from us?

Our engineering and manufacturing company develops and produces polypropylene bath tubs to the highest international quality standards. In the production and design process, polypropylene is used, only from proven European manufacturers with increased wear resistance and protection of the coating from UV rays, which is important when using a polypropylene hot tub in direct sunlight. Producing hot tubs since 2000, our company pursues an open pricing policy in relation to customers of our products. Thanks to this marketing approach, our polypropylene bath tubs are considered the best-selling products on the market.

===========================================================================================================

RosKedr

– a well-known manufacturer of goods made from Siberian cedar. Cedar or phyto-barrels are especially popular. They are actively advertised in the media and attract media personalities. The main specialization is the Cedar Barrel phytosauna. On the market since 2003. The main production is located in the Altai Republic.

Product features and range

The manufacturer's specialty is an emphasis on traditional cooperage technologies, refusal to use adhesives and coatings. A significant part of the work is done manually.

The range of hot tubs includes only 2 models, which are made of split staves. This ensures the hygroscopicity of the walls of the container and its tightness without the need for additional impregnation.

Watch a short video about the activity.
It contains a lot of interesting information about raw materials, their preparation, as well as about cooperage technologies used in the manufacture of barrels from chopped cedar. Characteristics of the RosKedr baths

Model	Single	Double
Form	Round	Oval
Material	Split cedar
Coating	No
Attaching the hoops	Rivets
Dimensions, H×L×W or H×D, cm	81×77	93×131×91
Equipment	Container, seat and its fastening, step, openwork hoops, passport and certificates. Additionally: decoration.
Estimated cost, rub.	35000	65000

Conclusion:

Despite the modest range of bathtubs, RosKedr can boast of products manufactured using traditional cooperage technologies. Such containers will fit perfectly into the surroundings of small Russian baths, filling them with the rich aroma of cedar wood.