Do-it-yourself bathhouse bench: 8 options

A bath bench is a mandatory piece of furniture for every bath room. Its design and manufacturing materials must fully comply with the functional tasks. The interior of any bathhouse or sauna is complete without comfortable, strong benches, benches and trestle beds made of high-quality and properly selected wood.

Making a bench for a bathhouse with your own hands: design options

There are many types of benches for a bath - stationary, movable, folding. For each bath room, specific benches are made, suitable only for a given place, shapes and sizes.

During bath procedures in the steam room, it is customary not to sit on a bench, but to lie down, and the number of lying places depends on the capacity of the room. Therefore, in order to increase the possible number of people steaming at the same time, benches of special systems are installed here.

Options for bath bench designs:

A simple mobile bench without a backrest on two legs, used in the washing area, in the rest room or in the steam room, including as a footrest.
A rustic-style bench with four legs is a strong, stable option for installation in a dressing room.
A portable bench for a steam room, its length can be from 90 to 151 cm, width approximately 50 cm;
Stationary single-tier shelf for the steam room. Its length is 150 - 185 cm and width 40 - 65 cm. The lower step should be at least 20 -25 cm from the floor for air circulation.
Two-tier wall shelf for steam room. It is installed if the room is not very large.
Three-tier shelf. The upper tier of shelves is made approximately 90 cm wide and 180 cm long, which allows an adult to sit comfortably. The distance from it to the ceiling should be at least 120cm. The lower shelves, 45–60 cm wide, are provided for seating.
Folding benches that have a special mechanism for turning the seat into a vertical position and tightly fixing it to the wall. Allows you to increase the usable area of a small room.
Portable benches with backs and armrests or trestle beds. Used in the rest room, installed near the table. They are usually large in size so that you can not only sit freely at the table, but also relax while lying down.

For the rest room, you can use furniture made of any wood and any design. The main thing is that it provides a comfortable and safe rest after the procedures.

Type of furniture

The photo of bath furniture shows different versions of manufactured items. These can be shelves, tables, benches, decorative items. All this will emphasize the original spirit of the room and complement the interior.

Before entering the room, some people use hangers and stands intended for shoes. The rest room is equipped with do-it-yourself bath furniture such as a bench or couch. If the area of the room allows them to be placed, you can thus equip a bathhouse.

The individual wishes of the owners play a significant role in the planning process. After all, some people like minimalism in everything, and the arrangement of a bathhouse is no exception.

For others, a bathhouse is a room with maximum comfort, in the arrangement of which every detail must be taken into account.

The most popular table shape is the rectangular model. Its parameters depend on the number of people who will be behind it.

Often, in order to rationally use free space, universal folding and folding models are used. They can be easily made independently, and this option significantly saves space.

Hallways 2020: TOP-200 photos of the best new products and modern design. Options for the ideal combination of color and style of furniture in the hallway
DIY stool: manufacturing methods and instructions for creating simple and stylish models (90 photo ideas)
Do-it-yourself door finishing: 115 photos of the best options for entrance and interior doors

You should consider the features of the bench. This attribute is mandatory, because it is used not only for washing and relaxing, but also as a shelf. The models differ from each other in the presence of spokes, length, width, and additional decorative elements.

Using carvings you can embellish the product. If you order a ready-made bench, you can indicate your individual wishes.

Shelves and hangers are also used for the bath. Collecting them does not take much time, and the items themselves do not take up much space. Often craftsmen transform standard forms into something original, special product. You can do the same.

Note! The bath furniture you make should be sustainable. Its surface is smooth for comfortable use.

It is also important to consider the size of the room. Accordingly, if your bathhouse is small, then you should select compact furniture for it, one that skillfully uses the limited space.

DIY cornice: a detailed description of how to design and decorate a stylish interior element (80 photos)
DIY folding chair: 110 photos, drawings, diagrams and sketches of convenient and easy options for creating portable chairs
Do-it-yourself pouf: step-by-step instructions on how to build a stylish and original interior element with your own hands (105 photos)

Experts also advise that during work, pay due attention to drawings and diagrams of furniture. You should not make furniture solid. You can make a small gap in the table top, or back, or seats. Thus, the material will dry faster, and accordingly, its service life will increase significantly.

How to make a bench for a bath: choosing materials

If a bathhouse building can be constructed from a variety of building materials, then bathhouse benches and other furniture can only be made of wood.

The benches of each bath room are made of wood specifically intended for it. No other materials other than wood are allowed for the manufacture of bath furniture.

When choosing materials, they simultaneously select the type of construction that would be combined with the style of the building. But in any case, there are certain rules for choosing wood based on experience and many years of practice.

Criteria for choosing wood for a bathhouse bench:

The steam room uses benches made of hardwood that can withstand high temperatures and humidity - oak, linden and larch. The aroma of these trees has healing properties.
Benches made of aspen and larch can be used in the washing room, since these materials tolerate high humidity well at relatively low air temperatures.
Furniture made from linden, aspen, larch, maple, oak or birch can be used in the relaxation room, however, due to increased moisture, all bath benches must be treated with special impregnations.

Benches and benches made of pine are never installed in the steam room, since under the influence of high temperatures, resin is released from the wood, which leaves marks on the body, but most importantly, it can cause a burn to the body.

There are increased requirements for the material of bath benches:

Moisture resistance, allowing the furniture to be used for a long time in conditions of high humidity.
Low thermal conductivity, in which the bench does not overheat in high temperature conditions, threatening burns.
High density wood so that it does not quickly become saturated with water, otherwise cracks will appear on the bench during use, it will rot and warp.
High drying speed. The bath bench should dry quickly and be easy to clean.

Linden is the best material for making bath benches, especially for use in steam rooms: it tolerates high temperatures well and is resistant to moisture, easy to process and emits a pleasant aroma. Aspen has also proven itself well, but over time, the furniture in the bathhouse begins to rot from the inside.

Coming from the East

In fact, to tell the truth, the divan is the legislative and executive body in a number of Islamic states, as well as its highest official. Who knows, perhaps the owners of furniture salons under the sonorous and popular name “Mr. Sofa” are very enlightened and erudite in all respects and are not as far from iron logic as it seems to us at first glance.

An indispensable attribute of any office are chairs; in the East, in the same legislative body, the function of such furniture was performed by benches with soft padding, so as not to particularly bother the users, or rather, their individual parts of the body. Actually, from there these important items went around the world, along the way, also acquiring a high back for greater comfort.

Bench for a bath: features of development and application

Benches for baths and saunas are used for both sitting and lying, so it is necessary to take into account the height and build of a person when designing them.

For a person of average height, the following dimensions of a bath bench are recommended:

Bench for sitting: their width is within 40 cm, height 50 – 95 cm.
Benches for saunas, on which they are placed in a semi-sitting position: at a height of 50 – 90 cm and a backrest height of 110 cm.
Benches for lying down: the width of the structure should be 90 cm, with a height of 50 cm. Such benches are made without a footrest.
The length of the bench per seated person is taken to be 90 cm. When using the bench by several people at the same time, the standard increases by 60 cm for each person.
When making a bench, it is necessary to provide for an arrangement of the legs of the bench that will not allow it to tip over when there is a load on the edge.

When creating benches for a bathhouse, you must pay attention to the dimensions of the room and not clutter it with unnecessary furniture that interferes with movement.

Shoe rack assembly technology

Making a shoe rack does not require a lot of time and labor, so you can cope with such a task in a couple of hours.

The shoe rack in the bathhouse is assembled and installed as follows:

2 side parts of the structure are being prepared, 35 cm wide and up to 90 cm high, as well as upper and lower parts 60 cm long.
The workpieces are thoroughly cleaned with fine-grain sandpaper or a grinder.
2 cuts are cut from the slats for the vertical shelf, the length of which is equal to the width of the side parts (35 cm). The parts are fixed to each other with self-tapping screws; the sides of the structure are reinforced with metal corners or wooden blocks.
Markings for the shelf are made on the side elements and holes of the required diameter are made.
The finished product is a box with sides, top and bottom slats, and a vertical shelf (or several shelves) for shoes.

The simplest bench for a bathhouse or sauna with your own hands: manufacturing technology

The simplest bench without a back consists of a plank seat, four timber legs and crossbars for stability.

The sequence of making a bench for a bath (sauna) is as follows:

We develop a drawing of the bench indicating all the structural elements of the product.
We cut the legs from 50 by 50 mm timber.
We cut grooves for attaching the cross beams on the inner sides of the legs.
We install the transverse bars in the grooves of the legs and fasten them with dowels.
We connect the legs using long bars, attaching them to the top of the legs with dowels.
We lay the boards on horizontal bars and secure them, leaving a gap of 1 cm.
We carefully process the bench with sanding discs, first with coarse-grained, and then with fine-grained abrasive. We round all the edges and sharp corners of the product.
We treat the bench with a special protective oil composition in 2 layers.

Leave the bench until the coating is completely dry. After the coating has dried, the bench can be installed in a sauna or bathhouse.

Processing methods

Wooden structures for baths are impregnated with special natural-based products. The use of oil-based varnishes and paints is unacceptable, since when heated they will smell unpleasant and release toxins. The following compounds will help protect benches from mold, fire, and rotting:

Oils. The products protect wooden products in the steam room from moisture and do not form a film on the surface.
Oil wax. Made from natural ingredients, used in washing and steam rooms. The composition does not emit toxic substances when heated strongly.
Bleaches. Contain oxidizing agents that prevent the formation of a dark shade.
Fire retardants. They are relevant if the sauna bench is installed next to an open fire or is operated at elevated temperatures. Such means prevent accidental fire of the product.

How to make a universal bench for your garden with your own hands

Before processing, the surface of the bench is thoroughly sanded and polished. The layers of wood are removed slowly and not too deeply. After this, the products are applied in 1–2 layers, and the bench is allowed to dry completely. It is recommended to carry out all procedures strictly according to the attached instructions.

Oils

Oil wax

Bleaches

Fire retardants